CONDTROL XP3 Green - Инструкция по эксплуатации - Страница 10

User manual

L A S ER DI S TANC E ME T ER

18

EN

19

User manual

L A S ER DI S TANC E ME T ER

EN

XP3 GREEN CONDTROL

XP3 GREEN CONDTROL

SAFE T Y REGUL ATIONS 

The user manual should be read carefully before you use the product for the first 

time.  Unintended use of the product can be dangerous for human’s health and 

cause serious injury. Keep this user manual. If the product is given to somebody 

for temporary use, be sure to enclose user manual to it.
- Do not misuse the product  
- Do not remove warning signs and protect them from abrasion, because they 

contain information about safe operation of the product. 
The device belongs to laser product class 2 in accordance with EN60825-1:

- Do not look into the laser beam or its reflection, with unprotected eye or through 

an optical instrument. Do not point the laser beam at people or animals without 

the need. You can dazzle them.

- To protect your eyes close them or look aside.

- It is prohibited to disassemble or repair the product yourself. Intrust product 

repair to qualified personnel and use original spare parts only.

- Do not use the product in explosive environment, close to flammable materials.

- Avoid heating the batteries to avoid the risk of explosion and electrolyte leakage. 

In case of liquid contact with skin, wash it immediately with soap and water. In 

case of contact with eyes, flush with clean water during 10 minutes and consult 

the doctor.

C ARE AND MAINTENANC E

Attention!

 The instrument is a precise device and requires careful handling. The 

following recommendations will extend the life of the product:
- Do not point the product at the sun
- Protect the product from bumps, falls, and excessive vibration; do not let liquids, 

construction dust and foreign objects get inside the product.
- Do not expose the product to extreme temperatures.
- If liquids get inside the product first remove the batteries, then contact a service 

center.
- Do not store or use the product under high humidity conditions for a long time.

- Clean the product with soft wet cloth.
- Keep device optics clean and protect it from mechanical damage.

- Сarry out control measurements occasionally, especially if the product is subject 

to excessive mechanical or other impact, before and after taking important 

measurements.

UTILIZ ATION

Expired tools, accessories and package should be passed for waste recycle. Please 

send the product to the following address for proper recycle:

CONDTROL GmbH 

Wasserburger Strasse 9 

84427 Sankt Wolfgang 

Germany 

Do not throw the product in municipal waste!

According  to  European  directive  2002/96/ЕC  expired  measuring  tools  and  their 

components must be collected separately and submitted to environmentally 

friendly recycle of wastes.

WARR ANT Y

All CONDTROL GmbH products go through post-production control and are 

governed by the following warranty terms. The buyer’s right to claim about defects 

and general provisions of the current legislation do not expire.

1) CONDTROL GmbH agrees to eliminate all defects in the product, discovered 

during the warranty period, that represent the defect in material or workmanship 

in full volume and at its own expense.
2) The warranty period is 36 months and starts from the date of purchase by the 

end consumer (see the original supporting document).
3) The warranty doesn’t cover defects resulting from wear and tear or improper 

use, malfunction of the product caused by failure to observe the instructions of 

this user manual, untimely maintenance and service and insufficient care, the use 

of non-original accessories and spare parts. Modifications in design of the product 

relieve the seller from responsibility for warranty works. The warranty does not 

cover cosmetic damage, that doesn’t hinder normal operation of the product.
4) CONDTROL GmbH reserves the right to decide on replacement or repair of the 

device.