Condtrol Vector 80 - Инструкция по эксплуатации

1

Vector 60/80

User manual

Laser distance meter

EN

Congratulations on your purchase of laser distance meter 

Vector 60/80 CONDTROL.

Safety instructions can be found in the end of this user manual 

and should be carefully read before you use the product for 

the first time.

SAFE T Y REGUL ATIONS 

The user manual should be read carefully before you use the 

product for the first time.  Unintended use of the product can 

be dangerous for human’s health and cause serious injury. 

Keep this user manual. If the product is given to somebody for 

temporary use, be sure to enclose user manual to it.

- Do not misuse the product 

- Do not remove warning signs and protect them from abrasion, 

because they contain information about safe operation of the 

product. 

The device belongs to laser product class 2 in accordance with 

EN60825-1.

Laser radiation!

Do not stare into beam

Class 2 laser

<1 mW 635nm

EN60825-1: 2007-03 

- Do not look into the laser beam or its reflection, with 

unprotected eye or through an optical instrument. Do not 

point the laser beam at people or animals without the need. 

You can dazzle them.

- To protect your eyes close them or look aside.

- It is prohibited to disassemble or repair the product yourself. 

Entrust product repair to qualified personnel and use original 

spare parts only.

- Do not use the product in explosive environment, close to 

flammable materials.

- Avoid heating the batteries to avoid the risk of explosion and 

electrolyte leakage. In case of liquid contact with skin, wash 

it immediately with soap and water. In case of contact with 

eyes, flush with clean water during 10 minutes and consult the 

doctor.

Vector 60/80

1. Display

2. Keyboard

3. A hole for the strap

4. End-piece

5. Tripod thread 1/4’’ 

6. Mini-USB connector for charging

Functions of buttons

Button

Short press

Long press

Switch on the 

device

Continuous 

measurement 

(tracking)

Switch on laser 

beam

Single distance 

measurement

Area

Memory

Wall surface*

Volume

Tilt sensor*

Pythagoras 1

Pythagoras 2

Pythagoras 3

Point to point*

Addition/

subtraction 

Select reference 

point

Stop measurement/

clear/exit the mode

Switch off the 

device

+

simultaneously

Select measuring 

unit 

*-Vector 80 only

Display

1. Main line for displaying measuring results

2. Additional lines for displaying measuring results

3. Indication of tilt angle

4. Indication of the mode

5. Indication of point to point function

6. Indication of Bluetooth

7. Indication of battery charge level

8. Indication of max/min values

9. Indication of reference point

10. Indication of measuring unit

11. Indication of memory

OPERATION

Battery charging

Charge level is shown on display. Charge the battery when 

symbol         appears on the display. Use USB charger delivered 

in the set only. 

It is not recommended to use the product while charging.

It takes approximately 3 hours to fully charge the batteries.

Switch on/off the device

To switch on the device short press                   .  

To switch off the device press and hold             during 1 second.

Measuring unit

Short press                       and                  simultaneously to enter 
service settings. Short press button                         to select 
required measuring unit – 

m/ft/in (meters/feet/inches)

. 

Short press                    to confirm and return to single distance 
measurement mode.

Reference point

Press and hold button               during 1 second to select 
the reference point. Appropriate indicator will appear on the 
display.

                          Front        Tripod         Rear           End-piece

                                                             (default)   

Measurements 

Single distance measurement 

Short press  

The device will switch on.

Short press  

Laser beam will switch on.

Point the laser beam at the object of 

measurement.

Short press  

Make a single distance 

measurement.

              - Measurement result

Short press  

Delete the last measurement result.

Continuous distance measurement (Tracking)

Press and hold  

during 

2 seconds

The device will start making 

measurements one after another, 

showing current measurement 

result in the main line, maximal value 

in the 1st line, minimal value in the 

2nd line.

 - Angle value

- Maximal value

- Minimal value

- Current value

Press                or 

Stop continuous measurement. 

The last measured values are shown 

on the display.

Addition/subtraction

Short press  

Turn on laser beam.

Aim the product at measured object.

Short press  

Take first measurement.

Measuring result appears in the main 

line.

Short press  

The symbol of addition/subtraction 

will appear on the display.

Short press  

Turn on laser beam. 1st measuring 

result moves to the line 2 on the 

display.

Short press  

Take 2nd measurement.

- 1st measurement

- 2nd measurement

- result of addition /subtraction 

To do addition/subtraction of more than 2 measurements 

short press           and perform the above mentioned 

operations required number of times.

Short press

Exit the mode.

CALCULATIONS
Area

Short 

press        

1 time.

Symbol           will appear on the 

display. Laser beam will be on. 

Short press  

Make the 1st measurement (length).

Short press  

Make the 2nd measurement (width).

Area (length and width 

multiplication) will be calculated 

and appear in the main line on the 

display.

- Length

- Width

- Area

Short press  

Exit the mode.

Wall surface (Vector 80 only)

Short 

press   

2 times.

Symbol               will appear on the 
display.    Laser beam will be on.

Short press  

Make the 1st measurement 

(height).

Short press  

Make the 2nd measurement 

(length 1).

INTENDED USE

Laser distance meters Vector 60 and Vector 80 are intended to 

measure distance, to calculate area and volume of measured 

objects, perform calculations by tilt sensor* and Pythagoras’ 

Theorem, point to point measurements*, store results of 

measurement/calculation in memory and also transmit via 

Bluetooth. The product is suitable for use at both indoor and 

outdoor building areas.

*-Vector 80 only.

DELIVERY PACKAGE

The delivery package includes:

1. Laser distance meter – 1pc.

2. Carry pouch with a strap - 1 pc.

3. User manual - 1 pc.

5. USB charger - 1 pc.

TECHNICAL SPECIFICATIONS

Vector 60

Vector 80

Measuring range*

0.05–60 m

0.05–80 m

Measuring accuracy **

± 1.5 mm

Smallest unit displayed

1 mm    

Display backlight

+

Reference point

Front, rear, tripod, end-piece

Continuous 

measurement (tracking)

+

Max./min. value

+

Addition/subtraction

+

Area/ volume

+

Calculations by 

Pythagoras’ Theorem

+

Bluetooth

+

Wall surface

-

+

Calculation of horizontal 

distance by tilt sensor

-

+

Point to point 

measurement

-

+

Memory

up to 30 values

Laser

Class II, 635 nm, <1 mW

Operating temperature

0 °С ... +40 °С

Storage temperature

–20 °С ... +60 °С

Dust and water 

protection

IP54

Power supply

3.7 V 850 mAh Li-ion

 rechargeable battery

Dimensions

119*46*28 mm

Weight

0.1 kg

* Use a reflective plate to increase the measurement range 

during daylight or if the target has poor reflection properties.

** Accuracy can decrease in unfavorable conditions, such as 

intense sunshine or when measurements are made against 

glossy or transparent surfaces, moving objects, objects with 

rough surface.

In unfavourable conditions or when measured distance is over 

100 m themaximum permissible accuracy is calculated in the 

following way:

± (Y + 0,25хDх10-3) mm, where

D (mm) - measured distance

Y (mm) - permissible accuracy according to technical data.

PRODUCT DESCRIPTION

Laser distance meter

Лазерный дальномер

Laser-Entfernungsmesser

EN
DE

RU

EN User manual                           1-2

DE Bedienungsanleitung                   3-4 

RU  Руководство     пользователя                          5-6

1

5

4

6

7

10

8

9

8

3

2

6

1

2

3

5

4

- Height

- Length 1

- Area

Short press  

Make the 3rd measurement 

(length 2)

- Height 

- Length 2

- Wall area

3rd, 4th, 5th etc. measurements can be done unlimited 

number of times. Each new wall surface is added to 

previously calculated wall area result.

Short press

Exit wall area calculation mode.

Volume

Short press   

2 times. 

(Vector 60)
Short press   

3 times. 

(Vector 80)

Symbol             will appear   on the 
display. Laser beam will be on.

Short press  

Make the first measurement 

(length).

Short press  

Make the 2nd measurement (width).

- Length

- Width

- Area

Short press  

Make the 3rd measurement (height).

- Width

- Height

- Volume

Short press

Exit the mode.

11