Oursson RF0480/RD - Инструкция по эксплуатации - Страница 14

14

TRANSPORTATION

, Рiс

. E

• 

Make sure there are no children or animals in the 

device. 

•  Move  and  transport  the  device  only  in  the  un

-

loaded condition.

•  It is recommended to move and place the device 

in two, Pic. E-1

•  Pack the device before moving it. 

•  When  moving  do  not  grab  or  pull  the  door  or  door’s 

handle.

•  When moving the device you cannot tilt it more than on 

45 degrees. Protect the device from excessive vibration 

and hits. Pic. E-2.

•  Please transport the device packed and in vertical po

-

sition. Improper transportation may result in injury and 

damage of the device.

POSSIBLE PROBLEMS AND SOLUTIONS

Possible problems

Possible causes

Solutions

D

evice isn’t working.

•  There is no voltage in the mains.

•  The cord is plugged incorrectly. 

•  Turn on the device. 

•  Check the main and the plug. If they are 

working, call the service center.

Vibrating noise .

The device is in unstable position. 

•  Adjust the position of the device.  

•  Move it if necessary.

The temperature is not cold 
enough

•  The door is not closed firmly.

•  Not enough ventilation

•  Make sure the door is firmly closed.

•  Clean the vents. 

The compressor is operating for 
a long period.

•  Ambient temperature is too high.

• 

The door is opened too often or 
remains open.

• 

Adjust the temperature of the room.

•  Make sure the door is firmly closed.

Frost accumulated on the rear 

side of the device.

• 

There is hot or moisture food in 

the device.

•  High humidity of the 

environment.

• 

Do not place hot or unpacked products into the 

device.

•  Adjust the humidity in the room.

Please check the possible problems before contacting a service center.

Reversing the door, 

Pic D-4

1

2

3

4

5

6

7

8

Top hinge cover

Top hinge screw
Top hinge

Cabinet plug

Bottom hinge
Door handle plug
Bottom hinge screw

Leveling leg

1. 

Remove top hinge cover 

1

 and top hinge screws 

2

which are below it. Then remove top hinge 

3

 . 

2. 

Remove cabinet plugs 

4

 and door handle plug 

6

. 

3. 

Remove the door. 

4. 

Remove right and left leveling legs 

8

. 

5. 

Remove the bottom hinge 

5

 and bottom hinge screws 

7

. 

6. 

Install the bottom hinge 

5

 on the other side of the lev

-

eling legs with bottom hinge screws 

7

. 

7. 

Install  right  and  left  leveling  legs 

8

. There are two 

holes below the refrigerator to fit the two levelling legs.

8.  Install the door. 
9.  Install the top hinge 

3

 on the other side with top hinge 

screws 

2

. 

10. 

Install  top  cover 

1

  above  the  top  hinge  and  install 

cabinet plugs 

4

 and door handle plug 

6

 on the other 

side.

11. 

Adjust the leveling legs 

8

.  

Note:

  Don’t  tilt  the  appliance  over  45°  when  revising  the 

door as possible damage to the sealed system may occur. 

CLEANING AND  MAINTENANCE, 

Рiс. F

•  Unplug the device.

•  Wash the inner parts of the device with a soft cloth and 

clean water with a detergent, then wipe everything with 

a cloth and clean water and wipe dry. 

• 

Contamination of the door gasket can cause damage 

to  it,  so  regularly  clean  it  with  a  soft  cloth  and  a  small 

amount of neutral detergent.

•  Outer  surface  of  the  device  must  be  cleaned  with  a 

slightly damp or dry cloth. 

•  Do  not  rub  with  detergent  the  informational  sticker  in

-

side  the  device,  because  printed  information  can  be 

erased. The information is necessary for service.

• 

Do not spill water on the electrical components of 

the device, as well as air vents because of the dan

-

ger of electric shock.