Sharp SJ-XE39PMBK - Инструкция по эксплуатации - Страница 18

18

WARNING

■ Unplug the refrigerator first to prevent electric shock.

■ Do not splash water directly on the outer cabinet or 

the interior. This may lead to rusting and deterioration 

of the electrical insulation.

IMPORTANT

To prevent cracking on inside surfaces and plastic 

components, follow these tips.

• Wipe any food oil adhered to plastic parts.

• Some household chemicals may cause damage, so use 

only diluted washing-up liquid (soapy water).

• If  undiluted  detergent  is  used  or  soapy  water  is  not  wiped 

of thoroughly, it may result in cracks of plastic parts.

1

  Remove the accessories (e.g. shelves) from the cabinet 

and the door. Wash them in warm soapy dishwashing 

water. After that, rinse them in clean water and dry.  

(Only fruit and vegetable shelf is not removable)

2

  Clean the inside with a cloth soaked in warm soapy 

dishwashing water. Then, use cold water to wipe off 

soapy water.

3

  Wipe the exterior with a soft cloth each time it is soiled.

4

  Clean the Magnetic door seal with a toothbrush and 

warm soapy dishwashing water.

5

  Wipe the control panel with a dry cloth.

NOTE

• Do not use heavy-duty cleansers or solvents (lacquer, paint, 

polishing powder, benzine, boiled water, etc.) to prevent your 

refrigerator from being damaged.

• If the power supply is stopped, wait 5 minutes at least before 

connecting the power plug again.

• The glass shelves weigh approximately 2 kg each. Hold firmly 

when removing from the cabinet or carrying.

• Do not drop objects inside the refrigerator or strike the inner 

wall. This may cause cracks to inner surface.

Defrosting

Defrosting is automated fully by a unique energy saving 

system.

When the compartment light is blown

Contact the service agent approved by SHARP to replace 

the light. The light is not to be replaced other than by 

qualified service personnel.

Switching off your refrigerator

If you want to switch your refrigerator off for an extended 

period, remove the foods from the refrigerator and clean the 

inside thoroughly. Pull out the power cord from the outlet 

and keep all doors open.

CARE AND CLEANING

Before calling for service, check the following points.

Problem

Solution

The outside of the cabinet is hot 

when touching. 

It is normal. The hot pipe is in the cabinet in order to prevent dew generation.

When there is refrigerator noise.

It is normal for the refrigerator to make the following sounds.

• Loud noise is made by the compressor when its operation starts  

--- Sound becomes quieter after a while.

• The compressor makes loud noise once a day.  

--- Operating sound is made immediately after automatic defrost operation.

• Sound of flowing fluid (gurgling sound, fizzing sound)  

--- Sound of refrigerant flowing in pipes (sound may become louder from time to time).

• Cracking or crunching sound, squeaking sound  

--- Sound produced by expansion and contraction of inner walls and internal parts 

during cooling.

Frost or dew appears inside or 

outside the refrigerator. 

This may occur in one of the following cases. Use a wet cloth for wiping frost and a dry 

cloth for wiping dew.

• When the ambient humidity is high.

• When the door is frequently opened and closed.

• When foods containing plenty of moisture are stored. (Wrapping is required.)

The foods in the refrigerator 

compartment freeze.

• Is the refrigerator operated for a long time with refrigerator temp. control set “MAX”?

• Is the refrigerator operated for a long time with freezer temp. control set “MAX”?

• Low ambient temperature may cause placed foods to freeze even if refrigerator temp. 

control is set to “MIN”.

It smells in the compartment.

• Wrapping is required for the foods with strong smell.

• Deodorizing unit cannot remove all of the smell.

Door alarm does not stop.

If the door alarm does not stop after closing all doors, it is a defect.

Contact the SHARP service center for service.

Method of stopping the door alarm temporarily.

Press “R” button and “F” button simultaneously  

and continuously for 3 seconds or more.
• The door alarm will sound again after approximately 2 days.

IF YOU STILL REQUIRE SERVICE

Refer to your nearest service agent approved by SHARP. 

BEFORE YOU CALL FOR SERVICE

Beep beep beep

(B803).indb   18

2017/02/17   14:53:33