Ryobi 36В RLM36x41H50G 5133005462 - Инструкция по эксплуатации - Страница 6

6

Original Instructions

■

A higher cutting height extends the run time 

of the battery pack.

TRANSPORTATION AND  STORAGE

■

Turn off the product, and remove the isolator 
key and the battery pack. Make sure that 
all moving parts have come to a complete 
stop. Allow the product to cool down before 
storing or transporting.

■

Remove all foreign materials from the 
product. Store the product in a cool, dry, and 
well-ventilated place that is inaccessible 
to children. Keep the product away from 
corrosive agents such as garden chemicals 
and de-icing salts. Do not store the product 
outdoors.

■

For transportation in vehicles, remove the 
isolator key, and secure the product against 
movement or falling to prevent injury to 
persons or damage to the product.

■

Use extreme caution when lifting or tilting 
the product for maintenance, cleaning, 
storage, or transportation. The blade is 
sharp. Keep all body parts away from the 
blade while it is exposed.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local 

and national provisions and regulations.
Follow all special requirements on packaging 

and labelling when transporting batteries by a 

third party. Ensure that no batteries can come 

in contact with other batteries or conductive 

materials while in transport by protecting 

exposed connectors with insulating, non-

conductive caps or tape. Do not transport 

batteries that are cracked or leaking. Check 

with the forwarding company for further advice.

MAINTENANCE

■

Use only original manufacturer’s 

replacement parts, accessories, and 

attachments. Failure to do so can cause 

possible injury, can contribute to poor 

performance, and may void your warranty.

■

Servicing requires extreme care and 

knowledge and should be performed only 

by a qualified service technician. Have the 

product serviced by an authorised service 

centre only.

■

Turn off the product, and remove the isolator 

key and the battery pack. Make sure that all 

moving parts have come to a complete stop 

before any cleaning or maintenance task.

■

Replace worn or damaged parts for safety.

■

Frequently check the grass catcher for wear 

or deterioration.

■

Check all nuts, bolts, and screws at frequent 

intervals for proper tightness to ensure that 

the product is in safe working condition.

■

Be careful during adjustment of the product 

to prevent entrapment of the fingers 

between moving blades and fixed parts of 

the product.

■

When servicing the blades, be aware that 

even though the power source is turned off, 

the blades can still be moved.

■

You may make adjustments and repairs 

described in this manual. For other repairs, 

have the product serviced by an authorised 

service centre only.

■

After each use, clean the plastic parts with 

a soft, dry cloth. Any part that is damaged 

should be properly repaired or replaced by 

an authorised service centre.

■

The blade on the product is sharp. Use 

extreme caution, and wear heavy-duty 

gloves when fitting, replacing, cleaning, or 

checking bolt security.

■

The blade bolts must be adequately 

tightened. See the manufacturer’s 

recommendations for blade bolt torque, 

which can be found in the product 

specification table in this manual.

CLEARING BLOCKAGES

■

Turn off the product, and remove the isolator 

key and the battery pack. Make sure that all 

moving parts have come to a complete stop.

■

Always wear heavy-duty gloves when 

checking or clearing a blockage. The blades 

are sharp, and the blockage itself could be 

a sharp object.

■

Remove the grass catcher. Check and carefully 

clear the grass catcher for obstructions.

■

Check the grass discharge chute, and 

carefully clear blockages.

■

Turn the product on its side. Check its 

underside and the area around the blade. 

Carefully remove any blockages. Remember 

that the blade may move during cleaning.