Husqvarna LC347iV 9679797-01 - Инструкция по эксплуатации - Страница 17

To start to use Husqvarna Connect

1. Download the Husqvarna Connect app on your

mobile device.

2. Register in the Husqvarna Connect app.
3. Do the instruction steps in the Husqvarna Connect

app to connect and register the product.

Bluetooth

®

 information (LC 247iX,

LC 347iVX, LC 353iVX)

Bluetooth

®

 wireless technology

The symbol for 

Bluetooth

®

 wireless technology comes

on when your mobile device is connected to the product.
(Fig. 32)

To set the product in operation position

1. Fold the handle to upright position. (Fig. 33)
2. Move the knobs up in the direction of the handle until

they stop and you hear a click. (Fig. 27)

3. Tighten the knobs fully.

To set the cutting height

The cutting height can be adjusted in 6 levels.
1. Move the cutting height lever down to decrease the

cutting height.

2. Move the cutting height lever up to increase the

cutting height. (Fig. 34)

CAUTION: Do not set the cutting height too

low. The blades can hit the ground if the

surface of the lawn is not level.

Battery

WARNING: Before you use the battery, you

must read and understand the safety

chapter. You must also read and understand

the operator's manual for the battery and the

battery charger.

Battery status

The display shows the remaining battery capacity and if

there are problems with the battery. The battery capacity

is shown for 5 seconds after the product is switched off

or the battery indicator button is pressed. The warning

symbol on the battery is on when an error has occurred.

See 

Battery on page 20.

(Fig. 35)

LED lights

Battery status

All LEDs are lit

Fully charged (75-100%)

LED 1, LED 2, LED 3 are

lit

The battery is 50%-75%

charged

LED lights

Battery status

LED 1, LED 2 are lit

The battery is 25%-50%

charged

LED 1 is lit

The battery is 0%-25%

charged.

LED 1 flashes

The battery is empty.

Charge the battery.

To charge the battery

Charge the battery before the first use. The battery is

only 30% charged when supplied to the customer.

Note: The battery charger must be connected to the

voltage and frequency specified on the rating plate.

The battery does not charge if the battery temperature is

above 50°C. The battery charger decreases the

temperature of the battery before it starts to charge.
1. Connect one end of the power cord for the battery

charger into the socket of the battery charger.

2. Connect the other end of the power cord for the

battery charger in an grounded mains socket. The

LED on the battery charger flashes green one time.

(Fig. 36)

3. Put the battery in the battery charger. The green light

on the charger comes on when the battery is

correctly connected to the battery charger. (Fig. 37)

4. When all LEDs on the battery have come on the

battery is fully charged. Charge the battery for

maximum 24 hours.

5. To disconnect the battery charger from the mains

socket, pull the plug, not the power cord.

6. Remove the battery from the battery charger.

Battery charging status

A Husqvarna Li-ion battery can be charged or used at all

charging levels. The battery is not damaged. A fully

charged battery will not decrease its charge when the

battery is left in the charger.

LED display

Charging status

LED 1 flashes

0%-25%

LED 1 is lit, LED 2 flashes 25%-50%

LED 1, LED 2 are lit, LED

3 flashes

50%-75%

LED 1, LED 2, LED 3 are

lit, LED 4 flashes

75%-100%

LED 1, LED 2, LED 3,

LED 4 are lit

Fully charged

1199 - 002 - 21.11.2019

17