Gardena PowerMax 34 05034-20.000.00 - Инструкция по эксплуатации - Страница 3

Voltage

Cable length

Cross section

220 – 240 V / 50 Hz

Up to 20 m

1.5 mm

2

220 – 240 V / 50 Hz

20 – 50 m

2.5 mm

2

  1.  Mains cables and extensions are available from your 

local Approved Service Centre.

  2.  Only use extension cables specifically designed for 

 outdoor use and which conform to one of the follow-

ing specifications: Ordinary rubber (60245 IEC 53), 

Ordinary PVC (60227 IEC 53) or Ordinary PCP  

(60245 IEC 57).

  3.  If the short connection lead is damaged, it must  

be replaced by the manufacturer, its service agent  

or similarly qualified persons in order to avoid  

a hazard.

Training
  1.  Read the instructions carefully. Be familiar with the 

controls and the correct use of the machine.

  2.  Never allow children or people unfamiliar with these 

instructions to use the machine. Local regulations can 

restrict the age of the operator.

  3.  Never operate the machine while people, especially 

children, or pets are nearby.

  4.  Keep in mind that the operator or user is responsible 

for accidents or hazards occurring to other people or 

their property.

Preparation
  1.  While operating the machine always wear substantial 

footwear and long trousers. Do not operate the 

machine when barefoot or wearing open sandals. 

Avoid wearing clothing that is loose fitting or that 

hanging cords or ties.

  2.  Thoroughly inspect the area where the machine is to 

be used and remove all objects which can be thrown 

by the machine.

  3.  Before using, always visually inspect to see that the 

blade, blade bolt and the blade assembly are not 

worn or damaged. Replace worn or damaged com-

ponents in set to preserve balance. Replace dam-

aged or unreadable labels.

  4.  Before use check the supply and extension cord for 

signs of damage or aging. If the cord becomes 

 damaged during use, disconnect the cord from the 

supply immediately. DO NOT TOUCH THE CORD 

BEFORE DISCONNECTING THE SUPPLY.  

Do not use the machine if the cord is damaged or 

worn.

Operation
  1.  Operate the machine only in daylight or in good 

 artificial  light.

  2.  Avoid operating the machine in wet grass.
  3.  Always be sure of your footing on slopes.
  4.  Walk, never run.
  5.  Mow across the face of slopes, never up and down.
  6.  Exercise extreme caution when changing direction on 

slopes.

  7.  Do not mow excessively steep slopes.
  8.  Use extreme caution when reversing or pulling the 

machine towards you.

  9.  Stop the blade(s) if the machine has to be tilted for 

transportation when crossing surfaces other than 

grass, and when transporting the machine to and 

from area to be used.

 10.  Never operate the machine with defective guards  

or shields, or without safety devices, for example 

deflectors and / or grass collector, in place.

 11.  Switch on the motor carefully according to instruc-

tions and with feet well away from the blade(s).

 12.  Do not tilt the machine when switching on the motor, 

except if the machine has to be tilted for starting.  

In this case, do not tilt it more than absolutely neces-

sary and lift only the part, which is away from the 

operator.

 13.  Do not start the machine when standing in front of the 

discharge opening.

 14.  Do not put hands or feet near or under rotating parts. 

Keep clear of the discharge opening at all times.

 15.  Do not transport the machine while the power source 

is running.

 16.  Stop the machine, and remove the plug from the 

socket. Make sure that all moving parts have come  

to a complete stop:

    • whenever you leave the machine,
    • before clearing blockages or unclogging chute,
    •  before checking, cleaning or working on the 

machine,

    •  after striking a foreign object. Inspect the machine 

for damage and make repairs before restarting and 

operating the machine;

    if the machine starts to vibrate abnormally  

(check immediately):

    • inspect for damage,
    • replace or repair any damaged parts,
    • check for and tighten any loose parts.

Maintenance and storage
  1.  Keep all nuts, bolts, and screws tight to be sure the 

machine is in safe working condition.

  2.  Check the grass collector frequently for wear or 

 deterioration.

  3.  On machines with multi blade, take care as rotating 

one blade can cause other blades rotate.

  4.  Be careful during adjustment of the machine to pre-

vent entrapment of the fingers between moving 

blades and fixed parts of the machine.

  5.  Always allow the machine to cool down before 

 storing.

  6.  When servicing the blades be aware that, even 

though the power source is switched off, the blades 

can still be moved.

  7.  Replace worn or damaged parts for safety. Use only 

genuine replacement parts and accessories.

14

GB