Газонокосилки AL-KO T 20-105.5 HDE V2 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
en
Operating the tractor
40
469590_a
With foot hydrostat drive:
The bypass lever (14a) is located in the rear right
wheel housing.
Bypass unlocking on T3 transmission (type: T15,
T16, T18)
Pull out the bypass lever (14a) and hook it in
upwards.
Release the brake.
➯
The lawn tractor can now be pushed.
Bypass unlocking on G700 transmission (type:
T20, T23)
Push in the bypass lever (14a) and hook it in
upwards.
Release the brake.
➯
The lawn tractor can now be pushed.
Starting and stopping the engine
Starting the engine
1. Sit on the operator's seat.
2. Press the brake pedal (4a) on the left side
down fully and lock it using the locking lever
(4b).
3. Make sure the mower mechanism is not swit-
ched on. Check the position of the toggle
switch (1e) for this purpose.
4. Move the controller (1b) for the engine speed
to the top stop. The choke symbol is located
there, depending on the equipment variant. If
it is not, pull the separate choke button (1a).
5. Insert the ignition key into the ignition lock
(1d).
6. Turn the ignition key to position "III" and hold
it there until the engine is running.
ADVICE
To reduce strain on the starter battery,
do not attempt to start for longer than
about 5 seconds.
7. Then release the ignition key, it automatically
jumps to position "II".
8. Move the controller (1b) for the engine speed
to the operating position. In an equipment va-
riant with the choke button, press it back in
again (1a).
Switching off the engine
1. Switch off the mower mechanism (1e).
2. Move the controller (1b) for the engine speed
to the idling speed position.
3. Press the brake pedal (4a) and lock it using
the locking lever (4b).
4. Turn the ignition key (1d) to position "0".
5. Remove the ignition key.
WARNING!
Danger if the engine is hot!
When stopping the engine, ensure that
hot engine components such as the si-
lencer cannot set fire to objects or mate-
rials located nearby!
Driving with the tractor
WARNING!
Danger in case of inappropriate
speed!
Drive slowly, especially at the beginning,
in order to familiarise yourself with the
driving and braking properties of the trac-
tor!
Before each change of direction, adjust
the driving speed so as to retain control
of the lawn tractor at all times, and to
prevent it from tipping over!
Your tractor is driven via a foot hydrostat trans-
mission.
Preparing to drive at temperatures below 10
°C.
ADVICE
1. Make sure the mower mechanism is
not switched on. Check the toggle
switch (1e) for this purpose.
2. Start the engine and let it run for
about 30 seconds to warm up and
optimise the gear oil viscosity. Follo-
wing that, you can drive the tractor.
Do not switch on the mower mecha-
nism until the engine has been run-
ning for a few minutes.
Driving with the foot hydrostat transmission
1. Press the brake pedal (4a) and lock it using
the locking lever (4b).
2. Set the mower mechanism to the maximum
cutting height (5b).
3. Start the engine.
4. Press the brake (4a).
5. Slowly press the foot pedal for the required
driving direction.
Forwards: Foot pedal (3b)
Reverse: Foot pedal (3a)
