Газонокосилки AL-KO BC 1200 E - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
15
GB
440 488 _a
People who are not familiar with the trimmer should
practice handling it while the motor is turned off.
Wear appropriate working clothes.
Make sure you can stand securely when working.
Always operate the machine with two hands.
Keep other people out of the danger area.
Do not leave the machine unsupervised.
When mowing on a slope, always stand below the
cutting device.
When working on a slope:
Never work on a smooth and slippery slope.
Always ensure that you are standing securely.
Always mow across the slope, never down or up.
Do not work on slopes with a more than 10°
gradient!
Pay particular attention when turning!
After contact with a foreign object:
Switch off the motor.
Check the machine for damage.
Do not operate the machine if you are under the
influence of alcohol, drugs or medication.
Comply with the accident prevention regulations.
Electrical safety
Caution!
Danger of touching live parts!
Immediately disconnect the plug from the mains if
the extension cable has been damaged or cut! We
recommend connecting via an RCCB with a rated
residual current < 30 mA.
The domestic mains voltage must match the
information relating to mains voltage in the technical
data; do not use any other supply voltage.
Only use extension cables that are intended for
outdoor use – minimum cross section 1.5 mm
2
. Always
reel in cable drums fully.
Do not use
damaged or brittle extension cables.
Check
the condition of your extension cable
before
each use.
Secure the extension cable in the cable strain relief.
Do not get the machine wet or expose it to moisture.
Keep children away from machines connected to the
mains.
Assembly
Important
The machine is not allowed to be operated unless
it has been fully assembled.
Installing the additional handle
(Fig. 2)
1. Place top part of handle (1) on the handlebar.
2. Place bottom part of handle (2) of the additional
handle underneath the handlebar on the top part of
the handle.
3. Loosely screw the parts of the handle together.
4. Align the handle on the handlebar and tighten the
screw connection.
Installing the guard plate holder
(Fig. 3)
1. Insert drive head (1) into guard plate holder (2).
Make sure that the screw-on surface for the guard
plate is located under the handlebar!
2. Firmly screw the guard plate holder onto the drive
head from underneath with three screws.
Installing the guard plate
(Fig. 4)
1. Place guard plate (1) on guard plate holder (2) and
align with the fastening holes.
2.
Use three cap screws and hex nuts to screw the
guard plate firmly onto the guard plate holder.
Installing the cutting blade
(Fig. 5)
1. Place cutting blade (2) on driver plate (1) so that the
hole in the cutting blade precisely aligns with the
guide circle in the driver plate.
2.
Push flange (3) onto the cutting blade so that the flat
side points towards the cutting blade.
3. Loosely screw fastening nut (4) anticlockwise onto the
guide pin of drive shaft (1).
4. Brace driver plate (1) using Allen key (6) and tighten
fastening nut (4) anticlockwise with hex key (5).
5. Secure the fastening nut with a split pin (Fig. 6/1).
Installing the spool
(Fig. 7)
The knife integrated in the guard plate
automatically cuts the line to the optimum length.
