Ryobi R18IDBL-0 (5133002662) - Инструкция по эксплуатации - Страница 4

2

| English

KNOW YOUR PRODUCT

See page 81.

1. Auto-load chuck
2. Tri-beam LED
3.  Direction of rotation selector
4.  Variable-speed switch trigger
5. Bit storage
6. Single bit
7. Battery port
8.  Mode selection button
9. Low speed
10. Medium speed
11. High speed
12. DECKDRIVE mode
13. Handle, insulated gripping surface

MODE SELECTION

The product features electronic speed control. Press the 
mode selection button to change the performance of the 
product to suit your application.
Changing the speed on an impact driver also effects the 
torque. For small screws, use speed 1. For a better control 
with mid-sized screws, use speed 2. For maximum speed 
and power when driving large screws, use speed 3.

'(&.'5,9( LV D PRGH SURJUDPPHG ZLWK D SUR¿OH WKDW

suits driving decking screws. It has a soft start-up to catch 
the screw thread, the impact driver then accelerates up to 
full speed before slowing down when the screw is almost 

ÀXVK WR DOORZ \RX WR VHW WKH VFUHZ KHDG FRUUHFWO\ 7KLV

SUR¿OHLVRSWLPLVHGIRUGULYLQJVFUHZVDURXQG[PP

LQWR VRIWZRRG GHFNLQJ DQG SUHVVXUH WUHDWHG SLQH MRLVWV

without a pilot hole.

MAINTENANCE

 WARNING

The product should never be connected to a power 

VXSSO\ ZKHQ DVVHPEOLQJ SDUWV PDNLQJ DGMXVWPHQWV

cleaning, performing maintenance, or when the product 
is not in use. Disconnecting the product from the power 
supply will prevent accidental starting that could cause 

VHULRXVLQMXU\

 WARNING

When servicing, use only original manufacturer’s 
replacement parts, accessories and attachments. Use of 
any other parts may create a hazard or cause product 
damage.

Ŷ

Avoid using solvents when cleaning plastic parts. Most 
plastics are susceptible to various types of commercial 
solvents and may be damaged by their use. Use clean 
cloths to remove dirt, carbon dust, etc.

 WARNING

'RQRWDWDQ\WLPHOHWEUDNHÀXLGVJDVROLQHSHWUROHXP

based products, penetrating oils, etc., come in contact 
with plastic parts. Chemicals can damage, weaken or 
destroy plastic which may result in serious personal 

LQMXU\

 WARNING

For greater safety and reliability, all repairs should be 
performed by an authorised service centre.

Ŷ

Always wear safety goggles or safety glasses with side 
shields during power tool operation or when blowing 
dust. If operation is dusty, also wear a dust mask.

LUBRICATION

All of the bearings in the product are lubricated with a 

VXI¿FLHQWDPRXQWRIKLJKJUDGHOXEULFDQWIRUWKHOLIHVSDQRI

the product under normal operating conditions. Therefore, 
no further lubrication is required.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing 
of as waste. The machine, accessories, and 
packaging should be sorted for environment-
friendly recycling.

SYMBOLS ON THE PRODUCT

Safety alert

CE conformity

EurAsian Conformity Mark

Ukrainian mark of conformity

Please read the instructions carefully 
before starting the machine.

No-load speed

V

Volts

Direct current

min

-1

Revolutions or reciprocations per minute