Einhell (4510080) - Инструкция по эксплуатации - Страница 17

GB

- 17 -

In section 10 (Charger indicator) you will 

fi

 nd a 

table with an explanation of the LED indicator on 

the charger.

If the battery pack fails to charge, check for the 

following:

• 

 voltage at the power socket

• 

 whether there is good contact at the charging 

contacts of the charging unit.

If the battery pack still fails to charge, send

• 

 the charger and charging adapter

• 

 and the battery pack

to our customer service center.

To ensure that items are properly packaged 

and delivered when you send them to us, 

please contact our customer service or the 

point of sale at which the equipment was 

purchased.

When shipping or disposing of batteries and 

cordless tools, always ensure that they are 

packed individually in plastic bags to prevent 

short circuits and 

fi

 res.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly. 

You must recharge the battery pack when you 

notice that the performance of the device drops. 

Never allow the battery pack to become fully di-

scharged. This will cause it to develop a defect.

6.2  Changeover switch (Fig. 4/Item 4)

The slide switch above the On/O

ff

  switch is for 

setting the direction of rotation of the cordless 

screwdriver and for preventing the cordless 

screwdriver from being switched on inadvertently. 

You can select between clockwise and counter-

clockwise rotation. To avoid causing damage to 

the gearing, the direction of rotation must only be 

changed when the equipment is at a standstill. 

When the slide switch is in the middle position, 

the On/O

ff

  switch is blocked.

6.3 On/O

ff

  switch (Fig. 4 / Item 3)

In

fi

 nitely variable speed control is possible with 

the On/O

ff

  switch. The further you push the 

switch, the higher the speed of the cordless 

screwdriver.

To switch on:

Press the On/O

ff

  switch (3).

To switch o

ff

 :

Release the ON/OFF switch (3)

6.4  Battery capacity indicator (Fig. 5 – Item d)

Press the battery capacity indicator switch (e). 

The battery capacity indicator (d) shows the char-

ge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED 

fl

 ashes:

The battery is empty, recharge the battery.

All LEDs blink:

The battery temperature is too low. Remove the 

battery from the equipment, keep it at room tem-

perature for one day. If the fault reoccurs, this me-

ans that the rechargeable battery has undergone 

exhaustive discharge and is defective. Remove 

the battery from the equipment. Never use or 

charge a defective battery.

6.5  LED lamp (Fig. 1/Item 2)

The LED lamp (2) can be used in poor lighting 

conditions to illuminate the area where you want 

to screw. The LED light (2) will come on automati-

cally as soon as you press the On/O

ff

  switch (3). 

6.6  Changing the bit (Fig. 6)

Important! Set the changeover switch (3) to its 

center position whenever you carry out any work 

(for example changing the tool, maintenance 

work, etc.) on the cordless screwdriver.

Fitting / removing the plug-in tool

Fit the required drive socket insert by pushing 

onto the square drive mount (1).

Remove the drive socket insert by pulling it o

ff

  the 

square drive mount (1).

6.7  Working with the impact driver

Loosening: 

• 

Mount a drive socket insert on the impact dri-

ver (see point 6.6).

• 

Place the impact driver on the screw/nut and 

loosen the screw/nut by pressing the On/Off 

switch (3).

• 

If the screws/nuts are very tight or if they are 

rusted, use a tire wrench or torque wrench to 

slightly loosen them.

Anl_IMPAXXO_18_230_SPK13.indb   17

Anl_IMPAXXO_18_230_SPK13.indb   17

14.12.2021   12:54:04

14.12.2021   12:54:04