Bosch GHO 40-82 C (060159A76A) - Инструкция по эксплуатации - Страница 15

 English | 

15

Bosch Power Tools

2 609 932 938 | (25.3.14)

Soft Starting

The electronic soft-starting feature limits the torque when 
switching on and increases the working life of the motor and 
drive belt.

Temperature Dependent Overload Protection

In case of overload, the speed is reduced. Allow the machine 
to cool down by running it at maximum no-load speed for ap-
prox. 30 seconds.

Working Advice

Planing (see figure G)

Set the required planing depth and place the front part of the 
planer base plate 

10

 against the workpiece.



Apply the machine to the workpiece only when 
switched on. 

Otherwise there is danger of kickback when 

the cutting tool jams in the workpiece.

Switch the machine on and guide the machine with even feed 
over the surface to be planed.

To achieve high-grade surfaces, work only with low feed and 
apply pressure on the centre of the planer base plate.

When machining hard materials (e. g. hardwood) as well as 
when utilising the maximum planer width, set only low planing 
depths and reduce planer feed, as required.

Excessive feed reduces the surface quality and can lead to 
rapid clogging of the chip ejector.

Only sharp blades achieve good cutting capacity and give the 
machine longer life.

The integrated park rest 

28

 also allows for continued planing 

at any given location on the workpiece after an interruption:

– With the park rest folded down, place the machine on the 

location of the workpiece where the planing is to be contin-
ued.

– Switch on the machine.
– Apply the supporting pressure onto the front part of the 

planer base plate and slowly push the machine forward 
(



). This tilts the park rest upward (



) so that the rear 

part of the planer base plate faces on the workpiece again.

– Guide the machine over the surface to be planed (



) with 

even feed.

Beveling Edges (see figure H)

The V-grooves in the front planer base plate allow quick and 
easy beveling of workpiece edges. Depending on required 
bevel width, use the corresponding V-groove. For this, place 
the planer with the V-groove onto the edge of the workpiece 
and guide it along the edge.

Planing with Parallel/Beveling Guide (see figures D – F)

Mount the parallel guide 

21

 or beveling guide 

24

 to the ma-

chine using the corresponding fastening bolt 

23

. Depending 

on the application, mount the rebating depth stop 

27

 with fas-

tening bolt 

26

 to the machine.

Loosen locking nut 

22

 and adjust the desired rebating width. 

Retighten locking nut 

22

.

Adjust the requested rebating depth accordingly with the re-
bating depth stop 

27

.

Carry out the planing procedure several times until the re-
quested rebating depth is reached. Guide the planer applying 
sideward supporting pressure.

Beveling with the Beveling Guide

When beveling rebates and 
surfaces, adjust the required 
slope angle with the angle ad-
justment 

25

.

Storage Compartment for Planer Blade/Allen Key

A planer blade 

16

 and an Allen key 

18

 can be housed in the 

storage compartment 

3

 as shown in the figure. To remove the 

contents in the compartment, completely pull the storage com-
partment for the planer blade/Allen key 

3

 out of the planer.

Service Station (see figure I)

The service station 

29

 in the carrying case can be used for 

holding the planer, e. g. for changing the blade.



Do not use the service station for stationary operation 
of the planer.

Maintenance and Service

Maintenance and Cleaning



Before any work on the machine itself, pull the mains 
plug.



For safe and proper working, always keep the machine 
and ventilation slots clean.

Ensure easy operation of the park rest 

28

 and clean it regular-

ly.
If the replacement of the supply cord is necessary, this has to 
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.

Groove to be used

Dimension a 
(mm)

none

0 – 5.7

small

1.9 – 7.6

medium

4.7 – 10.3

large

5.9 – 11.6

16

3

18

OBJ_BUCH-633-005.book  Page 15  Tuesday, March 25, 2014  9:45 AM