Bort BFB-850-T - Инструкция по эксплуатации - Страница 6

6

GB

Planer

INTENDED USE

This tool is intended for planing wooden materials such 
as beams and boards; it is also suitable for chamfering 
edges and rebating

TECHNICAL SPECIFICATIONS   

 1 

PRODUCT ELEMENTS   

 2 

1. Safety switch
2. On/off switch
3.  Knob for setting planing depth
4.  Planing depth indicator
5. Dust port

SAFETY

WARNING! Read all instructions. Failure to follow all 
instructions listed below may result in electric shock, 

fi

 re and/or serious injury. 

•  Avoid damage that can be caused by screws, nails 

and other elements in your workpiece; remove them 
before you start working

•  Always keep the cord away from moving parts of the 

tool; direct the cord to the rear away from the tool

•  Wait for the cutter block to stop before setting the 

tool down (an exposed knife may engage the sur-
face leading to possible loss of control and serious 
injury)

•  Use completely unrolled and safe extension cords 

with a capacity of 16 Amps (UK 13 Amps)

•  In case of electrical or mechanical malfunction, 

immediately switch off the tool and disconnect the 
plug

•  SBM Group can assure 

fl

 awless functioning of the 

tool only when original accessories are used

•  This tool should not be used by people under the 

age of 16 years

•  The noise level when working can exceed 85 dB(A); 

wear ear protection

•  Wear a dust protection mask when working with 

materials which produce dust that is detrimental to 
health; inform yourself beforehand about the materi-
als to be worked on

•  If the cord is damaged or cut through while working, 

do not touch the cord, but immediately disconnect 
the plug

•  Never use tool when cord is damaged; have it re-

placed by a quali

fi

 ed person

•  Always check that the supply voltage is the same as 

the voltage indicated on the nameplate of the tool 
(tools with a rating of 230V or 240V can also be con-
nected to a 220V supply)

•  If any chip should get jammed in the chip outlet, you 

should switch off the motor, ensure that all moving 
parts have come to a complete standstill, disconnect 
the plug, and remove the jammed chip

•  Before using the tool check that the knives do not 

brush anywhere

• Keep 

your 

fi

 ngers away from the rotating knives

•  Always disconnect plug from power source before 

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ON-

LY):

•  Do not connect the blue (= neutral) or brown (= live) 

wire in the cord of this tool to the earth terminal of 
the plug

•  If for any reason the old plug is cut off the cord of 

this tool, it must be disposed of safely and not left 
unattended

Your machine is double insulated in accord-
ance with EN 50144; therefore no earthwire 
is required.

MAINTENANCE

Make sure that the machine is not live when 
carrying out maintenance work on the motor. 

Regularly clean the machine housing with a soft cloth, 
preferably after each use. Keep the ventilation slots 
free from dust and dirt.If the dirt does not come off use 
a soft cloth moistened with soapy water. Never use 
solvents such as petrol, alcohol, ammonia water, etc. 
These solvents may damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please 
contact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during 
transport, it is delivered in a sturdy packaging. Most of 
the packaging materials can be recycled. Take these 
materials to the appropriate recycling locations. Take 
your unwanted machines to your local SBM Group 
dealer. Here they will be disposed of in an environmen-
tally safe way.

English