Einhell TE-MX 18 Li (4258760) - Инструкция по эксплуатации - Страница 17

GB

- 17 -

L

pA

 sound pressure level  ........................ 72 dB(A)

K

pA

 uncertainty  ............................................. 3 dB

L

WA

 sound power level   .......................... 83 dB(A)

K

WA

 uncertainty ............................................. 3 dB

Wear ear-mu

ff

 s.

The impact of noise can cause damage to hea-

ring.

Total vibration values (vector sum of three direc-

tions) determined in accordance with EN 62841.

Vibration emission value a

h

 = 5.54 m/s

2

K uncertainty = 1.5 m/s

2

The stated vibration emission levels and stated 

noise emission values were measured in ac-

cordance with a set of standardized criteria and 

can be used to compare one power tool with 

another.

The stated vibration emission levels and stated 

noise emission values can also be used to make 

an initial assessment of exposure.

Warning:

The vibration and noise emission levels may vary 

from the level speci

fi

 ed during actual use, depen-

ding on the way in which the power tool is used, 

especially the type of workpiece it is used for.

Keep the noise emissions and vibrations to a 

minimum.

• 

 Only use appliances which are in perfect wor-

king order.

• 

 Service and clean the appliance regularly.

• 

 Adapt your working style to suit the appliance.

• 

 Do not overload the appliance.

• 

 Have the appliance serviced whenever ne-

cessary.

• 

 Switch the appliance off when it is not in use.

• 

 Wear protective gloves.

Caution!

Residual risks

Even if you use this electric power tool in 

accordance with instructions, certain resi-

dual risks cannot be rules out. The following 

hazards may arise in connection with the 

equipment’s construction and layout:

1.   Lung damage if no suitable protective dust 

mask is used.

2.   Damage to hearing if no suitable ear protec-

tion is used.

3.   Health damage caused by hand-arm vib-

rations if the equipment is used over a pro-

longed period or is not properly guided and 

maintained.

5.  Before starting the equipment

5.1 Charging the Li battery pack (Fig. 2-3)

1.  Remove the battery pack (a) from the handle, 

pressing the pushlock button (b) downwards 

to do so.

2.  Check that your mains voltage is the same as 

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(c) into the socket outlet. The green LED will 

then begin to blink.

3.  Push the battery pack onto the battery char-

ger.

In section 10 (Charger indicator) you will 

fi

 nd a 

table with an explanation of the LED indicator on 

the charger.

If the battery pack fails to charge, check for the 

following: 

• 

 voltage at the power socket 

• 

 whether there is good contact at the charging 

contacts of the charging unit

If the battery pack still fails to charge, send 

• 

 the charging unit 

• 

 and the battery pack

to our customer service center.

5.2 Battery capacity indicator (Fig. 2/Item e)

Press the button for the battery capacity indicator 

(d). The battery capacity indicator (e) will indicate 

the charge status of the battery by means of 3 

LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED blinks:

The battery is empty, recharge the battery.

All LEDs blink:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a 

defective battery pack.

Anl_TE_MX_18_Li_SPK9.indb   17

Anl_TE_MX_18_Li_SPK9.indb   17

08.04.2019   15:06:44

08.04.2019   15:06:44