Bosch TWK8617P - Инструкция по эксплуатации - Страница 11

9

 en

Congratulations on purchasing this 

Bosch appliance. You have acquired 

a high-quality product that will bring 

you a lot of enjoyment. 

Parts and operating 

controls

1 

Kettle (with water level indicator)

2 

Lid

3 

Lid release button

4 

O

 ON/OFF switch

5 

Temperature indicator (illuminated)

6 

+ – button (temperature setting)

7  keep warm

 button

8 

Limescale filter (removable)

9 

Base

10 

Cable tidy

Important: 

Use the kettle only with its 

included base.

■

Only fill the kettle with water.

 Milk and 

instant beverages will burn and damage 

the appliance. Never operate the kettle 

without water and do not overfill it; 

observe the 

min

 and 

max

 markings. If 

the kettle is too full, the water will boil 

over! 

Before using 

for the first time

■ Remove any stickers or film.

■ Unroll the right amount of cable from the 

cable tidy and plug it in.

■ Fill the kettle with water. Bring the water 

to a boil and discard it. Repeat the 

procedure. This will make sure that the 

kettle is clean for normal use.

■ When the water comes to a boil for the 

first time, add a tablespoon of white 

vinegar.

W

Risk of fire!

Do not place the base or kettle on or near hot surfaces, e.g. hobs. 

Avoid spatters of grease as the plastic may be damaged.

W

Risk of scalding!

The appliance heats up during use. Make sure you only pick it up 

by the handle and do not open the lid until the appliance has cooled 

down. Only use the appliance when the lid is engaged.

If the appliance is filled above the “max” marking, there could be a 

risk from splashes of boiling water.

W

Risk of burns!

After the use the heating element surfaces and warming plate can 

be subjected to residual heat.

K

WARNING: Do not use this appliance near bathtubs, 

showers, basins or other vessels containing water.

W

Risk of suffocation!

Do not allow children to play with packaging material.

W

Risk of injury!

A misuse of the appliance can potentially lead to injury.

Boiling water

■ Fill the kettle with fresh water through the 

spout or the open lid (press lid release 

button).

■ Check the amount by reading the water 

level indicator markings 

min

 and 

max

. 

■ Close the lid until it locks and place the 

kettle on the base.

■ Press the 

O

 ON/OFF switch. The kettle 

emits a signal, and the factory-set 

temperature (100°C) lights up. The water 

is being heated.

■ By pressing button + or – you can set 

the temperature to ca. 70°C, ca. 80°C, 

ca. 90°C or ca. 100°C.

■ When the water has reached the selected 

temperature, the kettle will switch off 

automatically, the temperature indicator 

goes off, and a signal sounds.

Note: 

The selected temperature can be 

changed at any time while the kettle is 

heating up. While the kettle heats up, the 

current temperature lights up; the preset 

temperature flashes until it has been 

reached.

If the temperature cannot be set, this 

indicates that the water in the kettle is hotter 

than the desired temperature. The current 

temperature will light up. 

You can turn off the kettle at any time by 

pressing the 

O

 ON/OFF switch again.

Warning:

 If you remove the kettle from 

the base and replace it before the heating 

process is over, the kettle will not continue 

to heat the water. The selected settings will 

be lost (reset to factory setting).