Блендеры VITEK VT-3405 PR - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
5
ENGLISH
–
To avoid damaging the blades, do not pro-
cess too hard products such as cereals,
rice, spices, coffee beans, cheese and
frozen products.
–
When you use the blender attachment and
the products are hard to chop, add some
water, liquor or juice, if it is possible.
USING THE WHISK
Use the whisk attachment (8) only to beat cream,
make biscuit dough or for mixing ready desserts.
WARNING: Before assembling make sure
that the power plug is not inserted into the
mains socket.
•
Insert the whisk attachment (8) into the whisk
gear (9).
•
Attach the whisk gear (9) to the motor unit (3),
a click of the locks (2) means that the whisk
gear (9) is set properly.
•
Insert the power plug into the mains socket.
•
Put the whisk (8) into the bowl with products.
•
To switch the unit on, press and hold the but-
ton (5). Set the required rotation speed of the
whisk attachment (8) using the control knob
(6). Use this operation mode for mixing liq-
uid products.
•
If you press and hold the turbo mode button
(4), the unit will operate at maximum rota-
tion speed.
•
After you finish using the unit, take the power
plug out of the mains socket, disconnect the
whisk attachment (8) from the whisk gear (9)
and disconnect the gear (9) from the motor
unit (3) by pressing the locks (2).
Attention!
–
Do not use the whisk attachment (8) to
knead tight dough.
–
Products should be put into the bowl
before the unit is switched on.
USING THE MINI-CHOPPER
The chopper is used to chop meat, cheese,
onion, herbs, walnuts, almond, vegetables and
fruit.
Attention!
Do not chop very hard products, such as nut-
megs, coffee beans, cereals and ice.
Before you start chopping
•
Cut meat, cheese, onion, vegetables and fruit
into cubes approximately 2x2 cm in size.
•
Remove stems of herbs, peel the nuts.
•
Remove bones, sinews and cartilage from
meat.
Chopping
Caution: The blades of the chopping knife are
very sharp! Always hold the chopping knife
by the plastic end.
•
The chopper bowl (10) should be placed on a
flat stable surface.
•
Set the chopping knife (11) on the axis of the
chopper bowl (10).
•
Put the food into the chopper bowl (10).
Note:
–
Do not switch the unit on when the chopper
bowl (10) is empty.
•
Place the geared lid (12) on the chopper bowl
(10), having matched the ledges on the bowl
with the grooves on the geared lid (12), and turn
the geared lid (12) clockwise until bumping.
•
Place the motor unit (3) on the geared lid (12),
a click of the locks (2) shows that the motor
unit (3) is set properly.
•
To connect the unit to the mains, insert the
power cord plug into the mains socket.
•
To switch the unit on, press and hold the but-
ton (5). Set the required rotation speed of the
chopping knife (11) using the control knob (6).
•
When the turbo mode button (4) is pressed,
the knife rotates at maximal rotation speed.
•
During operation hold the motor unit (3) with
one hand and the chopper bowl (10) with the
other hand.
•
After using the unit, wait till the chopping knife
(11) fully stops.
•
Unplug the unit.
•
After using the chopper disconnect the motor
unit (3) from the geared lid (12) by pressing
the locks (2).
•
Remove the geared lid (12) by turning it coun-
terclockwise.
•
Carefully remove the chopping knife (11) tak-
ing it by the upper plastic end.
•
Take the chopped products out of the chop-
per bowl (10).
Attention!
Strictly follow the described sequence of
operations.
To achieve the best results, refer to the table
below.
VT-3405.indd 5
17.01.2014 10:28:14
