Блендеры VITEK VT-1474 ST - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
4
ENGLISH
•
Remove the lid (2) of the blender bowl.
•
Put the ingredients into the bowl (3).
•
Clover the blender bowl (3) with the lid
(2), insert the measuring cup into the lid
opening (2).
•
Once again make sure that the blender
bowl (3) is properly inserted and fixed.
•
Insert the plug into the socket.
Note:
The unit will not switch on if the blender bowl
or the blades set are not properly installed.
•
Use the operating modes switch (8) to set
the required mode
- “1” (low speed) – for mixing liquid products.
- “2” (high speed) – for liquid and hard
products.
- “Р” – pulse mode.
Note:
Time of continuous operation of the
blender should not exceed 3 min., and the
interval between operations should be not
less than 2 min.
AT TENTION:
•
Do not switch on the unit if the blender
bowl (3) is empty.
•
Do not fill the blender bowl (3) above the
maximal mark.
•
To add ingredients into the blender bowl
while mixing, remove the measuring cup
(1) from the lid (2), add ingredients through
the opening in the lid (2), gradually and in
small portions. Use the measuring cup (1)
to add liquids.
•
After operation, before removing the
products, switch off the unit setting the
switch (8) to the “O” position and take the
plug out of the socket.
•
Rotate the blender bowl (3) anticlockwise
and remove it from the motor unit (7).
•
Remove the lid (2) and remove the ready
products from the blender bowl (3).
•
Wash the blender bowl.
Cleaning and care
After operation switch off the unit and take the
plug out of the socket.
•
Wash all the removable parts with warm
water with a soft detergent and dry them
thoroughly.
•
Wipe the body of the blender with a soft,
slightly damp cloth.
•
Do not use hard sponges and abrasives.
•
Do not immerse the body of the blender
into any liquids and do not put it in a
dish wash machine.
Dismantling the blender bowl (3)
Note:
Wash the blades set (5) in the blender bowl
(3) before removing it.
•
Holding the blender bowl base (6), rotate
the bowl (3) anti clockwise and remove it
from the base (6).
•
Remove the blades set (5) from the bowl
base (6).
AT TENTION:
Blades are very sharp – handle them very
carefully!
•
Wash the blender bowl in warm water
with neutral detergent or use a dish wash
machine.
Assembling the blender bowl (3)
•
Put the sealing gasket (4) on the blades
set (5).
•
Put the blades set (5) into the blender bowl
base (6) in a way that the ledges on the
blades set (5) match the deepenings on
the bowl base (6).
•
Match the mark on the blender base (6)
with the mark on the blender bowl (3),
holding the base (6) rotate the blender
bowl (3) clockwise until bumping.
Note:
The unit will not switch on if the blades set
(5) is inserted improperly.
Storage
•
Before taking the unit away, make sure that
the unit is unplugged.
•
Perform the requirements of the CLEANING
AND CARE section.
•
Keep the unit in a dry clean place out of
reach of children.
4
ENGLISH
