BRAYER BR1245 - Инструкция по эксплуатации - Страница 5

8

9

EN

EN

•  Put the necessary ingredients in the bottle (7) (pic. 

2).

•  Install the knife block (5) on the bottle (7) and turn 

it clockwise (pic. 3). Do not make excessive efforts 

while turning the knife block (5).

•  Install the motor unit (2) in the knife block (5), turn the 

motor unit (2) clockwise until bumping (pic. 4), make 

sure that the motor unit (2) is fixed properly.

•  Insert the power plug into the mains socket.

•  Turn the blender with the bottle (7) up.

ATTENTION! Do not process the products if you 

hold the unit with the bottle down! (pic. 7) 

•  Press and hold down the button (4) to switch on, use 

this operating mode for mixing liquid products.

•  When you press and hold down the button (3) 

«TURBO», the blender will switch on at the maximal 

rotation speed. Use this mode to process liquid and 

hard products.

Note:

 do not switch the unit on when the bottle (7) is 

empty.
• 

Release the button (3 or 4) to switch the blender off.

• 

Unplug the unit after you finish using it. 

• 

After you finish cooking, turn the unit with the bottle 

(7) down.

•  Remove the motor unit (2) turning it 

counterclockwise.

•  Remove the knife block (5) from the bottle (7) turning 

the knife block (5) counterclockwise.

•  Pour the prepared products from the bottle (7) to a 

suitable container.

•  Wash the bottle (7) and the knife block (5) (only from 

the knives side).

ATTENTION: The knife block (5) cutting edges are 

very sharp and dangerous. Handle the knife block 

(5) carefully.

•  You can keep the ready food in the bottle (7). 

Remove the knife block (5) from the bottle (7) turning 

it counterclockwise, take the lid (6) and thread it 

rotating clockwise on the bottle (7). 

•  When you use the lid (6), open the valve, pour the 

necessary amount of liquid and close the valve.

•  Wash the bottle (7) and the lid (6) after the use.

CLEANING

• 

Unplug the unit after you finish using it. 

•  Wash the lid (6) and the bottle (7) with warm water 

and neutral detergent and dry them.

•  Wash only the lower part of the blender attachment 

(1), clean the outer surface with a slightly damp cloth. 

Never immerse the blender attachment (1) into water 

or any other liquids completely.

•  Wash the knife block (5) (only from the knives side) 

with warm water and neutral detergent, rinse and dry.

•  Clean the motor unit (2) with a soft, slightly damp 

cloth and then wipe it dry.

•  Do not immerse the motor unit (2), the blender 

attachment (1), the knife block (5) into any liquids, do 

not wash them under water jet or in a dishwashing 

machine.

•  Do not use abrasives and solvents to clean the motor 

unit body (2) and the removable parts.

STORAGE

•  Clean the unit parts before taking it away for long 

storage.

•  Do not wind the power cord around the motor unit 

(2).

•  Keep the unit in a dry cool place out of reach of 

children and disabled persons.

DELIVERY SET

1.  Motor unit – 1 pc.

2.  Blender attachment – 1 pc.

3.  Knife block – 1 pc.

4.  Bottle – 1 pc.

5.  Manual – 1 pc.

TECHNICAL SPECIFICATIONS

•  Power supply: 220-240 V ~ 50/60 Hz

•  Rated input power: 600 W

•  Bottle capacity: - 0,6 l

•  Maximal operation time: - 30 seconds

RECYCLING

 To prevent possible damage to the 

environment or harm to the health of 

people by uncontrolled waste disposal, 

after expiration of the service life of the 

unit or the batteries (if included), do not 

discard them with usual household waste, 

but take the unit and the batteries to specialized stations 

for further recycling.
The waste generated during the disposal of the unit 

is subject to mandatory collection and consequent 

disposal in the prescribed manner.
For further information about recycling of this product 

apply to a local municipal administration, a disposal 

service or to the shop where you purchased this 

product.
The manufacturer reserves the right to change the 

appearance, design and specifications not affecting 

general operation principles of the unit, without prior 

notice.

The unit operating life is 3 years

The manufacturing date is specified in the serial 

number.
In case of any malfunctions promptly apply to the 

authorized service center.