BRAYER BR1200WH - Инструкция по эксплуатации - Страница 4

6

7

EN

EN

• 

Examine the unit for damages; if the unit is damaged, 

do not plug it into the mains.

• 

Make sure that the indicated specifications of the 

power supply voltage of the unit correspond to 

the specifications of your mains. When the unit is 

powered from 60 Hz frequency mains, no additional 

actions are necessary.

•  Remove the lid (2) and remove the measuring cup 

(1).

• 

Wash the bowl (3), the lid (2) and the measuring cup 

(1) with warm water and neutral detergent, rinse and 

dry them.

• 

The cutting edges of the chopping knives (5) are 

sharp and can be dangerous, handle the chopping 

knives (5) carefully.

• 

Clean the motor unit body (7) with a soft, slightly 

damp cloth, and then wipe it dry.

• 

Do not immerse the unit, the power cord and the 

power plug of the unit into water or other liquids. 

USING THE BLENDER

ATTENTION! Continuous operation time of the 

blender should not exceed 1 minute, after that make 

at least 1 minute break.

• 

Note: 

— when using the unit for the first time, a 

foreign smell from the electric motor can appear — 

this is normal and it is not covered by warranty.

• 

Place the blender on a flat dry and steady surface.

•  Install the blender bowl (3) on the motor unit (7).

• 

Put the necessary ingredients into the bowl (3).

•  Cover the bowl (3) with the lid (2).

•  Insert the measuring cup (1) into the lid (2) opening.

• 

Notes: 

 -

the blender is not intended for beating eggs, 

making potato mash, 

 -

kneading dough, extracting fruit or vegetable juice, 

crushing hard or frozen products, chopping meat 

and meat products. 

 - the amount of food for processing should not 

exceed 2/3 of the capacity of the bowl (3) and 

should not be below the minimal mark «600» on 

the bowl (3).

 - use the scale on the bowl (3) to control the amount 

of products to process.

 -

before starting to chop/mix, we recommend to 

peel fruit, remove stones, and cut fruit into 2х2 cm 

cubes.

•  Insert the power plug into the socket.

• 

Set the knob (9) to the position «ON», the illumination 

(8) on the handle (9) will light up. 

• 

To switch the blender on and select the chopping 

knives (5) rotation speed set the knob (9) to a 

position from «MIN» to «MAX».

•  During the operation or between the operation 

cycles, you can add the required ingredients into the 

bowl (3). To do this, remove the measuring cup (1) 

from the lid (2). After adding ingredients through the 

lid (2) opening, install the measuring cup (1) back to 

its place.

• 

After you finish using the unit, set the knob (9) to the 

position «OFF», and unplug the unit.

BLENDER OPERATION MODES

• 

Set the knob (9) to the position «ON», the illumination 

(8) on the handle (9) will light up. 

• 

Press the button « » «SMOOTHIE» — cocktail 

making, the button «SMOOTHIE» illumination will 

light up and the blender will be switched on. To switch 

the blender off press the button « » «SMOOTHIE» 

again.

• 

To switch on the program « » «ICE CRUSHING» — 

ice crushing, press the button «ICE CRUSHING», 

the button illumination will light up, and the blender 

will be switched on in the ice crushing mode. To 

switch the blender off press the button « » «ICE 

CRUSHING» again.

• 

To switch on the pulse mode « » «PULSE», press 

and hold the button «PULSE», the button illumination 

will light up.

• 

After you finish using the unit, set the knob (9) to the 

position «OFF», and unplug the unit.

• 

Note: 

— if food processing is hindered, you can add 

some water, liquor or juice etc. into the blender bowl 

(3).

CLEANING AND  MAINTENANCE

• 

Wash the bowl (3) preliminary, to do this pour 

some water into the bowl (3) and add some neutral 

detergent.

•  Cover the bowl (3) with the lid (2) with installed 

measuring cup (1). 

•  Insert the power plug into the mains socket. 

• 

Set the knob (9) to the position «ON», the illumination 

(8) on the handle (9) will light up. 

• 

To switch on the pulse mode « » «PULSE», press 

and hold the button «PULSE», the button illumination 

will light up, after a few seconds release the button 

«PULSE».

• 

After you finish washing the bowl, set the knob (9) to 

the position «OFF», and unplug the unit.

•  Remove the lid (2) from the bowl (3).

• 

Remove the bowl (3) from the motor unit (7), drain 

the washing solution, wash the bowl, rinse it and dry.

• 

Wash the measuring cup (1), the lid (2) with warm 

water and neutral detergent, rinse it and dry.

REMOVING AND INSTALLING THE CHOPPING 

KNIVES (5)

• 

To remove the chopping knives (5) turn the lock 

(6) counterclockwICE and remove it. Remove the 

chopping knives (5) and the sealing gasket (4).