Ritter VERTICO7 - Инструкция по эксплуатации - Страница 18

14

–

Tall, narrow containers are 

more suitable than flat, wide 

ones.

–

If using a coated container, 

take care not to damage the 

coating during blending.

D

 To switch it on, first press and 

hold down the unlock button (7). 

Then, within 2 seconds, press the 

power button (8).

• 

Keep the unlock button 

pressed during operation.

The hand blender begins to oper-

ate at the highest speed setting. 

The LEDs on the LED display (6) 

light up (the number that light up 

depends on the current battery 

level).

Info:

To prevent the hand blender 

from overloading, the appliance 

will switch off automatically if it 

becomes overheated, if a blade 

becomes jammed or if the appli-

ance is operated continuously 

for more than 4 minutes. After 

it switches off, all LEDs flash 

slowly. You can then switch the 

blender on again and continue 

using it.

• 

Briefly press the power button 

again to adjust the speed if 

necessary.

This reduces the speed.

Info:

The next speed setting after the 

lowest speed setting is the high-

est speed setting.

• 

Release the unlock button to 

switch the appliance off.

Displaying the current battery 

level

• 

Briefly press the unlock but

-

ton (7).

The number of LEDs that light up 

indicates the current battery level.

English

CLEANING

CAUTION, risk of injury:

–

Keep your fingers away from 

the buttons to prevent the 

appliance from switching on 

accidentally.

–

The blades on the attach

-

ments are very sharp! Never 

touch these blades with your 

bare hands.

To prevent the accumulation 

of food residue, clean the 

blender (1) thoroughly after each 

use:

• 

Immerse the blender shaft (3) 

of the hand blender in the blender 

cup (14) or another container 

filled with warm water and 

detergent.

• 

Switch the hand blender on. 

Allow it to operate for a short 

period in the detergent solution.

• 

Fill the blender cup or con

-

tainer with clean, clear water and 

allow the hand blender to operate 

in the water for a short period.

•  To ensure that all food residue 

is removed, detach the blender 

attachment (see "Connecting/

replacing an attachment") and 

clean it.

• 

Use a damp cloth to wipe 

down the motor unit (2), blender 

shaft and charging station (13) if 

necessary.

NOTE, risk of damage to the 

hand blender:

–

Do not use any scouring 

agents, abrasive cleansers, 

sponges with rough surfaces 

or hard brushes.

– The hand blender is not 

suitable for washing in a 

dishwasher.

– Do not leave the blender 

shaft (3) sitting in liquid for a 

long time, as this may cause 

discolouration.

• 

Dry all parts that you have 

washed.

CHARGING THE BATTERY

If the blender (1) is switched on, 

the number of LEDs that light up 

on the LED display (6) indicates 

the current battery level. LED 1 

flashes slowly to indicate that the 

battery is dead.

Info:

Do not switch the blender on if 

the battery is dead. Otherwise, 

the battery may be damaged.

B

 Hook the hand blender (13) 

into the charging station by 

positioning it at an incline and 

then swivelling it into an upright 

position. 
The LEDs on the LED display 

flash to indicate that the hand 

blender is correctly connected to 

the charging station. The number 

of flashing LEDs indicates the 

current battery level.
Once the battery is fully loaded, 

all LEDs go out.

STORAGE

Keep the appliance and the 

accessories out of the reach of 

children. If storing the appli

-

ance for a longer period of time 

(without use), ensure that the 

battery is fully charged first 

(see "CHARGING THE BAT

-

TERY"). Otherwise, the battery 

may be damaged.